Nippon Paint 5L Zinc Phosphate Primer Grey Green

RM95.00 RM180.00

Nippon Paint 5L Zinc Phosphate Primer Grey Green

Price	RM95.00 RM180.00
Product SKU	0100090000005
Brand	Nippon Paint
Size (L x W x H)	200 mm x 200 mm x 250 mm
Availability	Out Of Stock

Product
Description
Reviews (0)
What's in the box

Description

Highlight

• Anti-Rust

• Fast dry

• Available Grey Green Colour

NIPPON PAINT Zinc Phosphate Primer

NIPPON ZINC PHOSPHATE PRIMER FD is an alkyd-based rust inhibitive primer for priming on iron and steel. It is recommended for iron and steel surfaces under non-immersion condition

Paint Type	Product Type	Finishing	Recommended Substrate	Pack Szie
Solvent based	Interior / Exterior	Low Gloss	Iron and Steel	1 Litre, 5 Litres, 20 Litres

Composition
Pegment	Anti rust and Extender
Binder	Alkyd
Thinner	White spirit
Technical Data
Drying Time	Touch Dry : 15 minutes (Dependent on temperature and humidity) Hard Dry : 4 hours (Dependent on temperature and humidity)
Overcoating Time (25°C to 30°C)	Minimum 8 hours (Dependent on temperature and humidity)
Typical Thickness	35 - 40 µm per coat
No. of Coats	1 - 2 coats
Theoretical Coverage	18.3 m2/litre (for dry film thickness of 30 microns) 12.2 m2/litre (for dry film thickness of 45 microns)
Practical Coverage	11.0 m2/litre (for dry film thickness of 30 microns)
Volume Solid	55 ± 3% by volume
Shelf Life	2Up to 24 months in tight sealed container
Recommendation Coating System
Iron and Steel
Sealer / Primer	Nippon Zinc Phosphate Primer FD : 1 Coat
Top Coat	Nippon Zinc Phosphate Primer FD : 1 Coats
Application Methods
Thinner	Nippon General Purpose Thinner
Brush/ Roller	: If necessary, add about 5% thinner by volume.
Compressed Air Spray	If necessary, add about 10% to 15% thinner by volume.
Airless Spray	:Delivery pressure :140 – 170 kg/cm2 :Tip size :0.015” – 0.017” :Spray angle : 60° - 70° : Dilution : Up to 5% thinner by volume
Cleaning
Cleaning Solvent	Nippon General Purpose Thinner. Clean up equipment with thinner immediately after use.
Surface Preparation
The surface to be painted shall be power tool cleaned to minimum SSPC-SP3 or St 3 ISO 8501- 1:2007, free from mill scale. It must be dry and free from dirt, grease, oil and other contaminants before application of the paint.
Environmental Conditions During Application
• Do not apply when the relative humidity exceeds 85% or when the surface to be coated is less than 3°C above the dew point. • Do not apply at temperature below 7℃. If not, drying and overcoating times will be considerably extended. • During application of the paint, naked flame, welding operations and smoking should not be allowed and good ventilation is necessary.
Safety Precautions
• Keep container tightly closed and keep out of reach children or away from food and drink. • Ensure good ventilation during application and drying. • During application of paint, naked flames, welding operation, and smoking should not be allowed. • When applying paint, it is advisable to wear eye protection. • In case of contact with eye, rinse with plenty of water immediately and seek medical advice. • Remove splashes from skin by using soap or water. • Paint must always be stored in a cool place. • When transporting paint, care must be taken. Always keep container in a secure upright position. • Dispose off any paint waste in accordance with the appropriate Environment Quality Regulations.
Note
* Theoretical Coverage is based on a mathematical formula and does not consider LOSS FACTORS. Variables like porosity of substrate, application method, dilution ratio, dry film thickness, opacity and so on will affect the loss factor and can vary from 30% - 50% or even more. The above information is given to the best of our knowledge based on laboratory tests and practical experience. However, since we cannot anticipate or control the many conditions under which our products may be used, we can only guarantee the quality of the product itself. We reserve the right to alter the given without prior notice.