Nippon Paint 18L 5100 Exterior Wall Sealer

RM230.00 RM250.00

Nippon Paint 18L 5100 Exterior Wall Sealer

Price	RM230.00 RM250.00
Product SKU	312X18WASE
Brand	Nippon Paint
Size (L x W x H)	300 mm x 300 mm x 350 mm
Availability	49

Quantity

Product
Description
Reviews (0)
What's in the box

Description

Highlight
								Good efflorescence resistance
Good for new walls and repainting
For exterior use
							

NIPPON PAINT 5100 Exterior Wall Sealer

5100 Wall Sealer is a styrene acrylic water-based wall sealer. It is specially formulated to protect the finishing coats against the effects of mild alkalinity and efflorescence.

PAINT TYPE	PRODUCT TYPE	FINISHING	RECOMMENDED SUBSTRATE	PACK SIZE
Water Based	Exterior	Mid Sheen	Masonry, brick, plastering substrate and fibre board	5 / 18Litres
COMPOSITION
PIGMENT	Titanium Dioxide and Mineral Extender
BINDER	Styrene Acrylic Emulsion
THINNER	Water
TECHNICAL DATA
DRYING TIME	Touch Dry : 15 minutes (Dependent on temperature and humidity) Hard Dry : 1 hour (Dependent on temperature and humidity)
RECOATING TIME	2 hours minimum (Dependent on temperature and humidity)
DRY FILM THICKNESS	Around 30 µm per coat (based on substrate condition)
NO. OF COATS	1 Coat
THEORETICAL COVERAGE	10 – 12 m2 per litre per coat (Actual coverage is dependent on substrate condition, application method, application condition and finishing appearance)
VOLUME SOLID	~38%
SHELF LIFE	Up to 36 months in tight sealed container
APPLICATON METHOD
BURSH / ROLLER	Dilute the paint with not more than 5% of water. Preferable not dilute for best performance.
RECOMMENDED COSTING SYSTEM
Emulsion Paint
SEALER / PRIMER	5100 Exterior Sealer : 1 coat
TOP COAT	Nippon Exterior Products : 2 coats
Tilelac Textured Coating
SEALER / PRIMER	5100 Exterior Seale : 1 coat
TEXTURED COAT	Tilelac Ema Base : 1 Coat
TOP COAT	Nippon Exterior Products : 2 coats
SURFACE PREPARATION
Remove all loose, defective paint or powdery residues, loose chalk, dust, fungus, algae and foreign matter. Treat any areas affected by fungus growth with Fungicidal Wash Solution. Repair cracks, uneven surfaces with suitable exterior grade fillers. Smoothen the filler areas with sand paper. Surfaces to be painted must be cleaned thoroughly and dry, it must be free from dirt, grease and other foreign matters. Allow all surfaces to dry completely prior to painting. Avoid painting when the moisture content and alkalinity of the walls are still high. (Recommended painting specification requires the moisture content of the walls to be below 16% measured by protimeter and alkalinity of the walls to be below pH9.) Spot prime with 5100 Wall Sealer.
CLEANING
Clean up equipment with water immediately after use.
SAFETY PRECAUTIONS
Keep container tightly closed and keep out of reach children or away from food and drink. Ensure good ventilation during application and drying. When applying paint, it is advisable to wear eye protection. In case of contact with eye, rinse with plenty of water immediately and seek medical advice. Remove splashes from skin by using soap or water. Paint must always be stored in a cool place. When transporting paint, care must be taken. Always keep container in a secure upright position. Dispose off any paint waste in accordance with the appropriate Environment Quality Regulations.
NOTES
* Theoretical Coverage is based on a mathematical formula and does not consider LOSS FACTORS. Variables like porosity of substrate, application method, dilution ratio, dry film thickness, opacity and so on will affect the loss factor and can vary from 30% - 50% or even more. The above information is given to the best of our knowledge based on laboratory tests and practical experience. However, since we cannot anticipate or control the many conditions under which our products may be used, we can only guarantee the quality of the product itself. We reserve the right to alter the given without prior notice.