Price | RM35.00 RM69.00 |
Product SKU | 0100090517001 |
Brand | Nippon Paint |
Size (L x W x H) | 100 mm x 100 mm x 150 mm |
Availability | 40 |
Quantity |
|
- Promotes better adhesion
- Good alkaline and efflorescence resistance
- Good for chalky and powdery surfaces
- For interior and exterior use
NIPPON PAINT Acrylic 5170 Wall Sealer
Nippon Acrylic 5170 Wall Sealer is a vinyl acrylate solvent-based sealer.It is specifically formulated to protect the finishing coats against the effects of alkalinity and moisture from the walls. Nippon Acrylic 5170 Wall Sealer is best used on interior and exterior walls, brickwork, plaster and asbestos-free substrates.
PAINT TYPE | PRODUCT TYPE | FINISHING | RECOMMENDED SUBSTRATE | PACK SIZE |
Solvent based | Interior/Exterior | Matt | Masonry wall, brickwork, plaster and asbestos free substrate | 1 / 5 / 20Litres |
COMPOSITION | ||||
PIGMENT | Titanium Dioxide and Mineral Extender | |||
BINDER | Acrylic Resin | |||
THINNER | Combination of ester, ketone and hydrocarbon | |||
TECHNICAL DATA | ||||
DRYING TIME |
Hard Dry : 2 hours (Dependent on temperature and humidity) |
|||
RECOATING TIME |
2 hours minimum (Dependent on temperature and humidity) |
|||
*Important Note: Drying Time and recoating time are strongly depending on environment ventilation, paint thickness, environment temperature, environment humidity, number of coats applied, thinner used to dilute product and recoat materials. So drying time and recoating time provided is for guide only. | ||||
DRY FILM THICKNESS | Around 30-35 µm per coat (based on substrate condition) | |||
NO. OF COATS |
1 Coat |
|||
THEORETICAL COVERAGE | 8 - 10 m2 per litre per coat (Actual coverage is dependent on substrate condition, application method, application condition and finishing appearance) | |||
VOLUME SOLID | ~58% | |||
SHELF LIFE | Up to 36 months in tight sealed container | |||
APPLICATON METHOD | ||||
BURSH / ROLLER | Ready for use after thorough stirring. If necessary, dilute with maximum 5% of Acrylic 3000 Thinner | |||
CONVENTIONAL AIR SPRAY | Dilute with 10% - 15% Acrylic 3000 Thinner. | |||
AIRLESS SPRAY | Ready for use after thorough stirring. | |||
RECOMMENDED COSTING SYSTEM | ||||
Emulsion Paint | ||||
SEALER / PRIMER |
Acrylic 5170 Wall Sealer : 1 coat |
|||
TOP COAT | Nippon Interior Products / Nippon Exterior Products : 2 coats | |||
Tilelac Textured Coating | ||||
SEALER / PRIMER | Acrylic 5170 Wall Sealer : 1 coat | |||
TEXTURED COAT | Tilelac Ema Base : 1 Coat | |||
TOP COAT | Acrylic Finish / Polyurethane Finish / PU Recoatable Finish / Weatherbond : 2 coats | |||
SURFACE PREPARATION | ||||
Remove all loose, defective paint or powdery residues, loose chalk, dust and foreign matter. Repair cracks, uneven surfaces with suitable fillers. Smoothen the filler areas with sand paper. Surfaces to be painted must be cleaned thoroughly and dry, it must be free from dirt, grease and other foreign matters. Allow all surfaces to dry completely prior to painting. Avoid painting when the moisture content and alkalinity of the walls are still high. (Recommended painting specification requires the moisture content of the walls to be below 16% measured by protimeter and alkalinity of the walls to be below pH9.) Spot prime with Acrylic 5170 Wall Sealer. | ||||
CLEANING | ||||
Clean up equipment with water immediately after use. | ||||
SAFETY PRECAUTIONS | ||||
|
||||
NOTES | ||||
* Theoretical Coverage is based on a mathematical formula
|
1 x Nippon Paint 5L Acrylic 5170 Interior/Exterior Wall Sealer