Touch Dry    : 2 hours (Dependent on temperature and humidity)

  Hard Dry      : 8 hours (Dependent on temperature and humidity)

  Drying time above is based on temperature 28 – 32 °C, humidity 70 – 80% and 5% dilution with Nippon General Purpose Thinner.

OVERCOATING TIME (25-30°C)

CURING TIME (25-30°C)

TYPICAL THICKNESS

  50 - 75 m dry film per coat

  80 - 125 m wet film per coat

  12.0 m2 per litre per coat (for dry film thickness of 50um)

   8.0 m2 per litre per coat (for dry film thickness of 75um)

PRACTICAL COVERAGE

(40% Loss Factor, as a guideline)

 7.2 m2 /litre (for dry film thickness of 50 microns)

 4.8 m2 /litre (for dry film thickness of 75 microns)

SPECIFIC GRAVITY

MIXING RATIO

Pot Life (25-30C)

4 parts by volume of Base to 1 part by volume of Hardener.

(Stir the content of the Base component, continue stirring and gradually add the total contents of the Hardener component, continue stirring until a homogeneous mix is obtained.)

   5 hours after mixing

   Up to 24 months in tight sealed container (Subjected to reinspection after exceeding shelf life period)

 Tcompressed air spray and airless spray. Preferably use airless spray if a thicker coat is required in one application. Brush, roller, and compressed air spray generally lead to lower film thickness, so more applications may be required to obtain the recommended thickness per coat.

 In order to ensure maximum adhesion between coats, it is important to observe that, before recoating, the applied coat is dry and free from any form of contamination. In case it rains or raining is expected, it is advisable not to do any painting. Painting under relative humidity above 85% will adversely affect the subsequent performance of the coating. Condensation occurs during or soon after application and premature early exposure to rain or ponding water could result in color and gloss change.

The optimum resistance of the coating is only attained after completion of the curing of the paint. Under average atmospheric conditions, it takes about 6 ~ 7 days. Exposure of the applied coating to severe abrasion or chemical and water spillage should therefore be avoided before completion of the curing period, the first two or three days being particularly critical.

THINNER

COMPRESSED AIR SPRAY

  Thin up to 5% by volume with Nippon PU Recoatable Thinner

  Delivery pressure: 140-170 kg/cm2

  Tip size: 0.015”-0.017”

  Spray Angle: 60° - 70°

  Nippon EA9/ Nippon Vinilex 5100 Wall Sealer : 1 coat

 Nippon 5100 Wall Sealer : 1 coat

 Nippon EA9 : 1 - 2 coat

  Nippon PU Recoatable Gloss / Soft Matt Finish  :  2 coats

 *Soft Matt only recommended for interior flooring

Wood

Surface must be dry and free from dirt, grease and other contaminants. Smoothen surface with sandpaper and then clean off and dry. The scraped areas should be spot-primed using an undercoat for wood surfaces.

Metal

Surface must be dry and free from dirt, grease and other contaminants. Ferrous substrate should be sanded or wire-brushed to remove millscales and rust. Clean off dust and dry. The scraped areas should be spot-primed using a primer for metal.

• Keep container tightly closed and keep out of reach children or away from food and drink.
• Ensure good ventilation during application and drying.
• When applying paint, it is advisable to wear eye protection.
• In case of contact with eye, rinse with plenty of water immediately and seek medical advice.
• Remove splashes from skin by using soap or water.
• Paint must always be stored in a cool place.
• When transporting paint, care must be taken. Always keep container in a secure upright position.
• Dispose off any paint waste in accordance with the appropriate Environment Quality Regulations.

* Theoretical Coverage is based on a mathematical formula

and does not consider LOSS FACTORS.
Variables like porosity of substrate, application method, dilution ratio, dry film thickness, opacity and so on will affect the
loss factor and can vary from 30% - 50% or even more.
The above information is given to the best of our knowledge based on laboratory tests and practical experience.
However, since we cannot anticipate or control the many conditions under which our products may be used, we can only
guarantee the quality of the product itself.
We reserve the right to alter the given without prior notice.